EASY 10 POINTS!! what are some good ideas for homemade instruments?!! i dont need drums...? - homemade flute headjoint
I need a homemade instrument to do just that and not some perecussion type of instrument.
A flute?
Please write the idea and how it works!
Easy 10 points !!!!!! I need it within 1 week and a half !!!!!!!!!!!!~!~!~
Wednesday, January 27, 2010
Homemade Flute Headjoint EASY 10 POINTS!! What Are Some Good Ideas For Homemade Instruments?!! I Dont Need Drums...?
4 comments:
Add Step1Use a funnel to a half cup of beans from around the world.
Step2Blow the world, that not to swallow the beans and fixed in a bun.
Step3Take toilet paper tube and cut a strip about two inches long, half-inch. Tape the toilet paper tube into the soil of the planet. The everyday things in the toilet paper tube and tape shut.
Step4Cover the balloon and toilet paper tube with paper mache. Papier mache can be made with equal parts water and flour. Flour and water. Bands Bad When the mixture is smooth newsprint paper making and cover the ball and tube of toilet paper. Allow to dry to the noise of paper mache house before you continue.
The rattle Step5Embellish homemade paper mache with paint, stickers, markers or construction paper.
Make This MIRAC
Flute:
Material
1 torchlight propane or butane or a campfire heat the metal bar.
1 steel rod of at least 1 / 2 inches in diameter
1 oven glove or heavy cloth
1 sawtooth that fineSierra ITS
1 pencil or pen fatty acids
1 sheet of fine grain sandpaper
Viejo 1 1 / 4 "Drill
1 pair of brackets around
1 Old Bamboo Fishing Rod
1 Measuring tape
Linseed oil and RAG
Instructions
Cut a piece of bamboo, at least 18 "to 20" long with a diameter between 3 / 4 "and 1" from the floor of an old fishing rod. Be sure to cut so is to end with a fiber material between the sections blocked to leave.
Measure and mark a point 1 "from the end sip from bamboo. Then a length measured from 6" mark and then the first five points to 1 inch. They should, when finished, has a total of seven brands.
Your next step is to use 1 / 2 "steel rod to burn the fibers are no longer necessary. For this purpose, red, extreme heat of the steel rod until Attention. * * Make - you use the oven glove or heavy canvas one to keep warm at the end of the rod and without heating. If the bar is hot, inserted into the open end of the bamboo and implementationTo burn a moderate force through the fibrous septa. Remember, the final (last holiday) part of the fibers intact
Then, heat the 1 / 4 "drill, until hot. Use clamps to collect and burn holes in places that you measured. Do not drill holes into the bamboo, as these can lead to cracking Bamboo
Take a piece of sandpaper grained approximately 3 "x3" and roll. Use sandpaper to remove the role of the charred bamboo around black holes that were burned. You can also use sandpaper to extend the borehole. This makes it easier to reach a sound, but be sure not to make the hole is too big. (
Rub a coat of linseed oil on the flute more. Do not cover the last six holes with the first three fingers of each hand. One by one hole, as you would in a soda bottle. Keep trying until you get a constant note. Now you can remove a finger to get a different sound. Experience and practice. Have fun.
I have this on ehow.com
Hello Karen! This is Sarah! I do not know whether this will be useful, but watch these videos on YouTube:
http://www.youtube.com/watch?v=qdcg8HQJs ...
http://www.youtube.com/watch?v=5V_hWBRZK ...
Sorry, I do not know how to do links. But you can copy and paste.
Hope this helps. :)
You can make a guitar with a roll of paper towels, a box of Kleenex and some rubber bands.
It really makes a lot of fun.
Impact soda bottles. I made it for bio .. in some fun, you can even different water .. it was good.
Post a Comment